Product Catalog    Case Studies     Find A Distributor

SOLUTIONS     RESULTS    LEARNING CENTER    ABOUT    CONTACT
Request A Quote

ADD-Vantage 9000

The ADD-Vantage 9000 includes OEI’s patented magnetic filter element as well as a stainless steel cloth element. Systems are optimized for fluid viscosity, flow volume, flow rate, temperature, mobility, and mounting requirements. Depending on the application, both “inside-out” and “outside-in” flow control designs are offered.

DESCRIPTION

The ADD-Vantage 9000 includes OEI’s patented magnetic filter element as well as a stainless steel cloth element. Systems are optimized for fluid viscosity, flow volume, flow rate, temperature, mobility, and mounting requirements. Depending on the application, both “inside-out” and “outside-in” flow control designs are offered.

Flow Control “Inside-out” flow control designs are recommended because the magnetic filter element is the primary filter. Its high holding capacity allows for extended operating life of the stainless steel cloth element which minimizes bypassing and extends cleaning intervals. “Outside-in” flow control operates with the stainless steel cloth element as the initial filter. The magnetic filter element acts as a secondary filter that enhances the systems filtration capability. If this filter goes into bypass, the magnetic filter element ensures continuous protection.

BENEFITS

» High holding capacity allows for extended planned maintenance periods
» Flows 43% more fluid or lube oil than conventional filters
» Continuous filtration in bypass
» Installs the same as conventional filters, no retrofitting required

EFFICIENCY

Magnetic Filter Element
Ferrous Contamination
Captures ferrous wear particles down to 4 μ and below with up to 95+% efficiency.
Non-ferrous Contamination
Non-ferrous particles are magnetically captured because of cross-contamination from static charge or embedded ferrous particles.
Stainless Steel Cloth Element
Absolute Rating
Pleated, Flat Screen, Perforated
10 μ, 25 μ, 40 μ, 150 μ
BETA 200
Exceeds ISO 16889 Standards
Eco-Coreless
Disposable Element Nominal Rating
Available on the Inline High-flow, High-volume
> 10 μ
BETA 200
10 μ, 25 μ
BETA 1000
Stainless steel Perforated Element
1/4″, 1/8″, 1/16″
Pressure/Temperature Rating
Standard Heat
< 34.4 bar (500 psi) @
< 121.1° C (250° F)
High Heat
< 34.4 bar (500 psi) @
< 204° C (400° F)
Viscosity Rating
< 1,000 cSt
Bypass Settings
» 0.3bar(5psi)
» 1bar(15psi)
» 3bar(45psi)
» 4.5bar(65psi)

MATERIALS

Magnetic Filter Element
Rare-earth magnets configured in a patented radial field design
Filter Housing, End Caps, Mounts
Standard
Carbon Steel
Non-Corrosive
Stainless Steel
Pleated, Flat Screen, Perforated Cloth-Media Element
Stainless Steel
Eco-Coreless Disposable Elements Available on the Inline High-flow, High-volume
Z-media (Synthetic)
Seals
Standard
Buna
High Heat
Viton
Sub-zero
EDPM

INSTALLATION

Port Size
1/2” – 3”
Port Type
»NPT »ORB
»CD62 »BSPT
»CD61 »BSPP

LIMITED WARRANTY

Magnetic Filter Element
3 years
Housing and Components
1 year
Mount Type
» Spin-on
»Inline
»Remote
» In-tank
Element Clearance
Housing length + 4”

SERVICE LIFE

Magnetic Filter Element
18+ years
Stainless Steel Cloth Element
5 years

CLEANING

Magnetic Filter Element: Remove the contamination by wiping downward with a lab cloth or rubber glove.
Stainless Steel Cloth Element: Separate the filter element from the bypass assembly and clean with a solvent, soap and water, a parts washer, or ultrasonically. Then let the element air dry.

Use the magnetic filter element as a predictive maintenance tool by removing contamination with a lab cloth or rubber glove and depositing it into a sample jar. Send the contamination for analysis to determine the source of equipment component wear and prevent system failure.

SERIES SPECIFICATIONS

TYPE
DESCRIPTION
PART NUMBER
PORT SIZE
HOUSING SIZE
FLOW CONTROL
FLOW RATE
@ 68 cSt
PRESSURE RATING
TEMP. RATING
MAGNETIC FILTER ELEMENT
DIRECT SPIN-ON
ADD-Vantage 9000’s that spin directly onto OEM mounts.
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
REMOTE MOUNT SPIN-ON
ADD-Vantage 9000’s that spin directly onto OEM mounts.
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
IN-TANK
ADD-Vantage 9000’s that spin directly onto OEM mounts.
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
INLINE
ADD-Vantage 9000’s that spin directly onto OEM mounts.
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
9ADV9-#
1/2” – 1 1/2”
35/8”ODx 71/2”L
Outside-in
21 gpm (75 L/min)
< 34.4 bar (500 psi)
105° C (221° F)
1/2”OD
EMBEDDED FLUID CLEANLI- NESS GUIDE

DOWNLOAD THE

GUIDE TO FLUID CLEANLINESS

4344 12th Street SE Calgary, AB T2G 3H9 Canada
(403) 242 4221 quotes@oneeyeindustries.com

SOLUTIONS

>HYDRAULICS
>PNEUMATICS
>PUMPS
>ENGINES
>FUEL SYSTEMS
>COOALNT LINES
>GEARBOXES
> COMPRESSORS
> TOTAL PROTECTION KITS
> WATER SYSTEMS
> PRODUCT LINES
> PARTS WASHERS
> MILLING MACHINES

INDUSTRIES

> O&G WELL STIMULATION
> O&G PLANT
> POWER GENERATION
> PULP & PAPER
> MANUFACTURING
> FOOD PROCESSING
> MILITARY
> MINING
> TRANSPORTATION
> BUILDING OPERATIONS
> RENEWABLE ENERGY
> MUNICIPALITY